RASPBERRY PI 5

The new High Quality 16mm 10MP Telephoto Camera Lens from Raspberry Pi is compatible with C or CS-mount lenses.

Please note: Raspberry Pi High Quality Camera not included - available separately here.

The 16mm 10MP Telephoto lens offers a high level of zoom, for targeting your camera on specific subjects. The lenses screw directly onto the Raspberry Pi High Quality Camera and feature multiple adjustment options (via thumbscrews) for greater flexibility and image refinement. Covers for the front and rear of the lenses are included and come pre-fitted.

Features

Compatible with the Raspberry Pi High Quality Camera

Thumbscrew adjustment

Covers on front and back

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

Raspberry Pi Zero

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. It offers an IMX708 12-megapixel sensor with HDR, and features phase detection autofocus. Camera Module 3 is available in standard and wide-angle variants, both of which are available with or without an infrared cut filter.

Camera Module 3 can be used to take full HD video as well as stills photographs, and features an HDR mode up to 3 megapixels. Its operation is fully supported by the libcamera library, including Camera Module 3’s rapid autofocus feature: this makes it easy for beginners to use, while offering plenty for advanced users. Camera Module 3 is compatible with all Raspberry Pi computers.

The PCB size and mounting holes remain the same as for Camera Module 2. The Z dimension differs: due to the improved optics, Camera Module 3 is several millimetres taller than Camera Module 2.

Key Features:

Back-illuminated 12-megapixel Sony IMX708 sensor

High signal-to-noise ratio (SNR)

Integrated 2D Dynamic Defect Pixel Correction (DPC)

Fast Phase Detection Autofocus (PDAF)

QBC Re-mosaic function

HDR mode supporting up to 3-megapixel output

CSI-2 data output

I2C fast-mode compatible serial communication

2-wire serial control for focus mechanism

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

Raspberry Pi Zero

The Raspberry Pi Active Cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case.

The Active Cooler combines a large metal heatsink with a high-quality variable-speed blower fan, powered and controlled via the fan connector on the Raspberry Pi 5, attached to the board via sprung pins into the dedicated pair of mounting holes.

As the heat from the Pi 5 CPU spreads across the heatsink body and fins, the blower fan pushes cool air over them to keep your Raspberry Pi 5 running at optimal thermal levels. The cooler uses thermal pads to create a solid thermal connection with the Raspberry Pi 5.

The fan is software-controlled, allowing it to remain off (and therefore silent) until temperatures reach the specified threshold.

Features

Compatible with Raspberry Pi 5

Large metal 'finned' heatsink combined with a high-quality blower fan

Fan fitting compatible with the Raspberry Pi 5 fan connector

Variable speed fan (software/temperature controlled)

Uses the Raspberry Pi 5 heatsink mount holes

Thermal pads included (pre-fitted)

Raspberry Pi not included

Compatible with:

Raspberry Pi 5

A 128x64 pixel, 2.15" LCD display with snazzy six-zone RGB backlight and six capacitive touch buttons. GFX HAT makes an ideal display and interface for your headless Pi projects.

GFX HAT riffs off the previous Display-O-Tron HAT (now discontinued), but gives you the flexibility of individual pixels, letting you display more complex graphics and real typefaces, while retaining the handy capacitive touch buttons for input/navigation.

Features:

128x64 pixel, 2.15" LCD display

Integrated diffuser/reflector assembly

Six-zone RGB LED backlight

SN3218 LED driver chip (I2C address 0x54)

Six capacitive touch buttons with white LEDs

Microchip CAP1166 capacitive touch/LED driver chip ((I2C address 0x2c)

Compatible with all 40-pin header Raspberry Pi models

Python library

Comes fully assembled

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

The Official Raspberry Pi MicroSD card adapter!

Convert your Micro SD card into a full-sized SD - great for fitting into PC/laptop SD card readers for flashing a new OS with Raspberry Pi Imager.

The adapter includes the Raspberry Pi logo on the front for an extra bit of 'cool'!

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

Raspberry Pi Pico

Raspberry Pi Zero

The Raspberry Pi 27W USB-C Power Supply is an ideal power supply for Raspberry Pi 5 and Pi 4, especially for users who wish to drive high-power peripherals, such as hard drives and SSDs, from Raspberry Pi 5’s four Type A USB ports.

Delivering a maximum of 5.1V, 5A, it supports USB PD (Power Delivery), so Raspberry Pi 5 can communicate with it and select the most appropriate power profile. This enables Raspberry Pi 5 to increase the USB current limit automatically from the default 600mA to 1.6A, in order to provide extra power for devices connected to the four Type A USB ports.

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

The Raspberry Piofficial keyboard includes three host USB ports for connecting external devices, such as USB Raspberry Pi mouse, USB drives, and other USB controlled devices. The product’s micro USB port is for connection to the Raspberry Pi. Via the USB hub built into the keyboard, the Raspberry Pi controls, and provides power to, the three USB Type A ports.

Note: If using with a Pi Zero, you'll need a OTG adapter cable.

Keyboard Features: The Raspberry Pi keyboard has three lock keys: Num Lock, Scroll Lock, and Caps Lock. There are three LEDs in the top right-hand corner that indicate which locks are enabled.

Num Lock – Allows use of the red number keys on the letter keys, effectively creating a numeric keypad. This mode is enabled and disabled by pressing the Num Lock key.

Caps Lock – Allows typing capital letters; press the Shift key to type lower-case letters in this mode. This mode is enabled and disabled by pressing the Caps Lock key.

Scroll Lock (ScrLk) – Allows use of the cursor keys for browsing web pages and spreadsheets without the mouse. This mode is enabled and disabled by pressing the ScrLk key while holding the Fn key.

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Documents:

Raspberry Pi Official Keyboard and Mouse

The official Raspberry Pi Mouse is a 3-button optical mouse with a scroll wheel, designed for comfortable use with your Raspberry Pi.

Mouse Specification

Three-button optical mouse

Scroll wheel

USB type-A connector

Compatible with all Raspberry Pi products (with full-size USB ports)

Ergonomic design for comfortable use

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

This 175mm long GPIO (general purpose input/output) ribbon cable lets you extend the reach of your Raspberry Pi's pins, bridging them out to other boards or PCBs. The Raspberry Pi's GPIO can be used for all sorts: twiddling pins on or off, providing 3.3V or 5V power, communicating with I2C or SPI devices, and much more. This cable gives you a bit more flexibility in where you route those signals.

175mm long x 51mm wide

40 wires, 2x20 pin female connectors

Pin 1 is marked by the white/pink wire

Note: Be careful to connect this cable to your board the correct way around. You can't use it with a male header to connect to a HAT's female header, as the pins will be mirrored. You'll risk damaging both your board and your Raspberry Pi if you connect the cable incorrectly so, if in doubt, check the order of the pins on the connector with a multimeter before connecting things up!

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

A low-energy, high-falutin, electronic paper (ePaper / eInk / EPD) display for your Pi, in black/white!

Inky pHAT's beautiful, high contrast display is ideal for displaying simple graphics and crisply-rendered text and, because it's like paper, it's readable in bright sunlight. You could use Inky pHAT as a cute little clock, display tweets on it, the weather, news headlines, sports scores, and more. It's also ideal for graphing data from remote sensors, CPU load or temperature, or stock prices.

Features:

2.13" EPD display

Inky pHAT pinout

Compatible with all 40-pin header Raspberry Pi models

Python library

Comes fully assembled

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Headerfor Pi Zero)

Unlock a world of possibilities with the Raspberry Pi Pimoroni Explorer's Hat Pro for 40 Pin. Seamlessly integrate sensors, buttons, and LEDs into your Raspberry Pi projects, transforming them into interactive experiences. Whether you're building robots, IoT devices, or custom interfaces, this Hat delivers unparalleled control and functionality. Its compact form factor and easy-to-use design make it the ideal choice for makers of all skill levels. Elevate your Raspberry Pi projects with the Pimoroni Explorer's Hat Pro and explore the endless potential of your creations.

Four buffered 5V tolerant inputs (perfect for Arduino compatibility)

Four powered 5V outputs (up to 500mA total across all four channels)

Four capacitive touch pads (labelled 1, 2, 3, 4)

Four capacitive crocodile clip pads (labelled 5, 6, 7, 8)

Four coloured LEDs (red, green, blue, and yellow)

Four analog inputs

Two H-bridge motor drivers (up to 200mA per channel; soft PWM control)

A heap of useful (unprotected) 3v3 goodies from the GPIO

A mini breadboard on top!

Explorer HAT Pro pinout

Compatible with all 40-pin header Raspberry Pi models/li>

Python library

Comes fully assembled

Notes
The inputs use a 5-channel buffer that will accept anything from 2V-5V as logic high
Mini breadboard had 170 points, 17x5 per half of the breadboard

Compatible with:

Raspberry Pi 4

Raspberry Pi 5

Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Headerfor Pi Zero)

Keep track of your surroundings using Enviro for Raspberry Pi! Equipped with a variety of advanced environmental sensors, these boards feature a beautiful full-color LCD screen to showcase your data. They offer an ideal introduction to citizen science and environmental monitoring!

Enviro is designed for indoor monitoring, letting you measure temperature, pressure, humidity, light, and noise level. It's great for keeping tabs on what's going on in rooms in your house, office, or elsewhere. Push the data to server and you can view the data remotely from anywhere.

BME280 temperature, pressure, humidity sensor (datasheet)

LTR-559 light and proximity sensor (datasheet)

MEMS microphone (datasheet)

0.96" colour LCD (160x80)

Pimoroni breakout-compatible pin header

pHAT-format board

Fully-assembled

Compatible with all 40-pin header Raspberry Pi models

Python library

Dimensions: 65x30x8.5mm

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Raspberry Pi Zero (but needs Male 40-pin 2x20 HAT Headerfor Pi Zero)

A generous 2.0" (320 x 240) IPS LCD display for Raspberry Pi with lots of tasty baked in functionality.

Display HAT Mini features a bright 18-bit capable 320x240 pixel display with vibrant colours and formidable IPS viewing angles, connected via SPI. It's got four tactile buttons for interacting with your Pi with your digits and a RGB LED for notifications. Pimoroni have also squeezed in a QwST connector (Qwiic / STEMMA QT) and a Breakout Garden header so it's a doddle to connect up different kinds of breakouts.

It will work with any model of Pi with a 40 pin header, it goes with the Raspberry Pi Zero particularly well - Pimoroni have included a pair of standoffs so you can use to bolt HAT and Pi together to make a sturdy little unit. To accommodate the screen Display HAT Mini is a bit bigger than a standard mini HAT or pHAT - it's around 5mm taller than a Pi Zero (so a Mini HAT XL or a Mini HAT Pro, if you will).

Display HAT Mini lets you turn a Raspberry Pi into a convenient IoT control panel, a tiny photo frame, digital art display or gif-box, or a desktop display for news headlines, tweets, or other info from online APIs. This screen is a handy 3:2 ratio, useful for retro gaming purposes!

Features:

2.0” 320x240 pixel IPS LCD screen, connected via SPI (~220 PPI, 65K colours)

4 x tactile buttons

RGB LED

Qw/ST (Qwiic/STEMMA QT) connector

Breakout Garden / I2C header

Pre-soldered socket header for attaching to Raspberry Pi

Compatible with all models of Raspberry Pi with a 40 pin header.

Fully assembled

No soldering required (as long as your Pi has header pins attached).

Dimensions: approx 65.5mm x 35mm x 9mm (W x H x D, includes header and display). With a Pi Zero attached with standoffs, the total depth is 17mm.

Screen usable area: 40.8mm x 30.6mm (L x W)

Pinout

Schematic

Dimensional drawing

Display HAT Mini Python library

ST7789 Python library

Includes

Display HAT Mini

2 x 10mm standoffs

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Headerfor Pi Zero)

Plug Pirate Audio Line-out for Raspberry Pi into your hi-fi amp or powered speakers, then sit back, relax, and soak in the rich, digital audio. It has a high-quality I2S DAC, high-res colour display, and playback control buttons.

This board is perfect for upgrading an existing hi-fi amp and speakers, or a set of powered monitors, with digital audio from local audio files (MP3, FLAC, etc.) or from streaming services. The DAC on Pirate Audio Line-out gives you crisp 24-bit / 192KHz digital audio through its 3.5mm stereo jack.

Pirate Audio is a range of all-in-one audio boards for Raspberry Pi, with high-quality digital audio, beautifully-crisp IPS displays for album art, tactile buttons for playback control, and our custom Pirate Audio software and installer to make setting it all up a breeze.

Features:

Line-level digital audio (24-bit / 192KHz) over I2S

PCM5100A DAC chip (datasheet)

3.5mm stereo jack

1.3" IPS colour LCD (240x240px) (ST7789 driver)

Four tactile buttons

Mini HAT-format board

Fully-assembled

Compatible with all 40-pin header Raspberry Pi models

Pirate Audio software

Dimensions: 65x30.5x9.5mm

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Headerfor Pi Zero)

These headers will give your HAT or pHAT a real lift! We all love playing with the latest Pi accessories, but sometimes we've found that these wonderful add-on boards could do with just a little more clearance from the top of the Raspberry Pi.

That's where these little headers come in! They're standard 2x20 GPIO headers so are suitable for all 40-pin versions of the Raspberry Pi, but they have 5mm pins to make sure they mate securely with the female headers on your add-on board.

Datasheet

Compatible with:

Raspberry Pi 5

Raspberry Pi 4

Light, flexible, and stable, the perfect partner for the Raspberry Pi High Quality Camera

The three flexible legs will hold your camera stable on your desk, or can be wrapped around a support for more unusual placements. The head is also on a ball joint, so the camera can be angled to get the perfect shot! Fitted with a standard 1/4"-20 camera mount the tripod will mate securely with the Raspberry Pi High Quality Camera, but can also be used with a wide variety of other products including GoPro. The rubber feet will keep your camera from sliding and the lightweight and compact construction makes this usefully portable.

Colour may differ from picture.

Compatible with:

Raspberry Pi High Quality Camera

Pibow 5 lets you access all the ports and connectors on your Pi and even has a clever little tab that will let you push the Pi 5's brand new power button whilst it's safely ensconced in its case. The case is designed to fit neatly around Raspberry Pi's new Active Cooler.

Crafted out of five unique layers including a transparent top that leaves your beautiful Pi visible inside. Each layer is laser-cut from high-quality cast acrylic and once stacked they securely contain a Raspberry Pi 5 while leaving the primary ports and GPIO accessible. This case is lightweight and ideal for mounting to any surface. No tools are required for assembly or disassembly!

Features:

Compatible with Raspberry Pi 5 only 

Compatible with Raspberry Pi 5 Official Active Cooler

Super-slimline profile

Fully HAT/pHAT compatible

Protects your beloved Pi 5!

Clear top leaves Raspberry Pi 5 visible (so you can gaze upon its wonder).

GPIO cut-out

Leaves all ports and connectors accessible

External Power Button Nubbin via compliant mechanism magic

Mounting holes on the base that will accommodate M2.5 screws/bolts and the studs on popular Danish ABS construction blocks 

Made from lightweight high-quality cast acrylic

Great for hacking and tinkering!

The Raspberry Pi 5 provides two MIPI connectors to use with displays (DSI) or camera modules. These connectors are smaller than previous generations of Raspberry Pi, so you'll need one of these adapter cables to use your Raspberry Pi touchscreen display.

These camera cables DO NOT work with DSI displays. You'll need a different cable for displays - they are not interchangeable!

These camera adapter cables have a 22-way 0.5mm-pitch connection at one end (for the Raspberry Pi 5 end), and a 15-way 1mm-pitch connector at the other (for your camera). These cables have CAMERA clearly printed on them so that you don't get them mixed up with the very similar-looking display cables.

Features

Camera adapter cable for Raspberry Pi 5

For use with camera modules only (not compatible with DSI displays)

22-way 0.5mm pitch to 15-way 1mm-pitch

FPC cable (Flexible Printed Circuit)

CAMERA printed on the cable body for easy identification

Length : 200mm

Compatible with:

Raspberry Pi 5

The Raspberry Pi 5 includes two MIPI connectors designed for camera modules or displays. These connectors are more compact than those on previous Raspberry Pi models, so an adapter cable is required to connect your camera module.

Cable length: 200mm

These adapter cables feature a 22-pin, 0.5mm-pitch connector on one side for the Raspberry Pi 5, and a 15-pin, 1mm-pitch connector on the opposite side.

These camera cables DO NOT work with DSI displays.

Expand your connectivity options with the Raspberry Pi USB 3 Hub, transforming a single USB-A port into four accessible connections. This versatile hub includes an optional USB-C power input to support high-power devices, while standard power works perfectly for lower-energy peripherals. Designed to work smoothly across all Raspberry Pi models, the USB 3 Hub is ideal for enhancing your setup with ease.