Search
All Categories
Menu Close

Kitronik ZIP Circle - 12 ZIP LEDs

Manufacturer: Kitronik
Each of these new ZIP Circles has 12 individually addressable RGB LED’s. Each LED can be controlled independently and all LEDs are connected using the same three wire bus. Each LED can produce a full spectrum of colours independent to all of the other LEDs on the bus. Each ZIP LED has a Red, Green and Blue element within the LED, and each of these can achieve 256 levels of brightness. This results in 16,777,216 possible output colours. Multiple ZIP LEDs can be connected to produce longer strings/strips.

The LEDs used are based on the WS2812B part which is compatible with any WS2812B driver code. They can also be coded in the MakeCode Block/Javascript editor.

Features:
  • Simple 3 wire connection for all LEDs.
  • Compatible with any WS2812B driver code.
  • They can be coded with the Microsoft MakeCode Editor for the BBC microbit.
  • Integrated reset circuit.

  • Dimensions:
  • Width: 7.5mm.
  • Height: 3mm.
  • PCB Height: 1.5mm.
  • Inner Diameter: 29.2mm.
  • Outer Diameter: 44.2mm.
  • SKU: KI 35135
    Availability: 15 in stock
    €7.75
    i h
    Please select the address you want to ship to
    Ship to
    *
    *
    Shipping Method
    Name
    Estimated Delivery
    Price
    No shipping options
    Customers who bought this item also bought
    Picture of Kitronik Flat Profile Tact Switch (Buzzer)

    Kitronik Flat Profile Tact Switch (Buzzer)

    KI 3420
  • A low profile Miniature PCB Mount TACT Switch.
  • Single pole normally open contact.
  • Max voltage = 24V DC.
  • Max current = 50mA. L 6, W 6, H 4.3 mm.
  • L 6, W 6, H 4.3 mm.
  • This part is found in the Kitronik Inventors Kit
  • €0.50
    Picture of Grove - Ultrasonic Distance Sensor obs25

    Grove - Ultrasonic Distance Sensor obs25

    KI 46153
    The Grove Ultrasonic Distance Sensor is an ultrasonic transducer that utilizes ultrasonic waves to measures distance. It can measure from 3cm to 350cm with the accuracy up to 2mm. It is a perfect ultrasonic module for distance measurement, proximity sensors, and ultrasonic detector.

    This module has an ultrasonic transmitter and an ultrasonic receiver so you can consider it as an ultrasonic transceiver. Similar to sonar, when the 40KHz ultrasonic wave generated by the transmitter encounters the object, the sound wave will be reflected back, and the receiver can receive the reflected ultrasonic wave. It calculates the time from the transmission to the reception, and then multiplies it by the speed of the sound in the air(340 m/s) to calculate the distance from the sensor to the object.

    Compared with traditional ultrasonic module, the HC-SR04, the Grove Ultrasonic Distance Sensor integrates a single-chip microcomputer, and the transmitting signal and the receiving signal share one pin by time division multiplexing, so only one I/O pin is occupied. Another difference is that HC-SR04 only supports 5v voltage, while Grove - Ultrasonic Distance Sensor supports 5v and 3.3v. As we know, the Raspberry pi I/O only supports 3.3v. Therefore, Grove - Ultrasonic Distance Sensor can be directly connected to the I/O of the Raspberry Pi, but HC-SR04 needs to use a voltage conversion circuit.

    Features:
  • 3.3V/5V compatible, wide voltage level: 3.2V ∼ 5.2V.
  • Only 3 pins needed, save I/O resources.
  • Wide measurement range of 3cm ∼ 350cm.
  • Easy to use, grove connector, plug and play.

  • Possible Applications:
  • Distance measurement.
  • Ultrasonic detector.
  • Proximity alarm.
  • Smart car/buggy/robot.

  • Dimensions:
  • Length: 50mm.
  • Width: 25mm.
  • Height: 16mm.
  • €10.95
    Picture of Kitronik Jumper Wires 20cm Male to Male 40 Pack

    Kitronik Jumper Wires 20cm Male to Male 40 Pack

    KI 4110-40
    These are 20cm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header.

  • Male to Male connectors
  • 40 x M/M Jumpers (four of each colour)
  • Length: 20cm (approx)
  • €3.95
    Picture of Kitronik Jumper Wires 20cm Male / Female 40 Pack

    Kitronik Jumper Wires 20cm Male / Female 40 Pack

    KI 4128-40
    These are 20cm long jumpers with male connectors on one end and female on the other. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.

  • Male to Female connectors
  • Pack of 40 x M/F Jumpers (four of each colour)
  • Length: 20cm (approx)
  • €3.95