ELECTRONIC ACCESSORIES

These wheels are specifically designed for use with FS90R micro continuous rotation servo and also fit the Mini 360 degree continuous rotation servo. The wheel presses onto the servo spline just like a typical servo horn, and the small screw included with the FS90R accessory pack for mounting servo horns should be used to hold the wheel in place.

The wheels have silicone press fit tyres and measure 60mm in diameter.

Features:

Silicone press fit tyres.

Ideal for use with a Mini 360 degree continuos rotation servo.

Contents:

1 x Black Wheel for FS90R Micro Servo, 60×8mm.

Dimensions:

Diameter: 60mm.

Tyre Width: 8mm.

If you have a robotics project or buggy featuring geared hobby motors, these 5 spoke injection moulded ABS wheels are the perfect wheel for the job! They fit directly onto the geared hobby motors TT style shaft and can be screw fixed firmly in place. The ABS used is very lightweight and has excellent mechanical qualities. As such, the wheels are extremely durable and very difficult to break. As they are made from ABS the wheels can be fully recycled.

The wheels are supplied with rubber o-rings that when pushed onto the wheel act as tyres. When fitted, the o-rings will not come off accidentally. A concerted effort is required to remove them.

Features:

Sturdy 5 Spoke design.

Injection moulded with matte green ABS.

The ABS used is lightweight and has very good mechanical properties making them durable and difficult to break.

Supplied with rubber 0-rings that fit to the wheel and act as tyers.

Can also be used as a drive pulley for projects such as a ferris wheel or lazy Susan.

Push fit for TT shaft geared hobby motors. The wheel can then be screw fixed to the motor to ensure it stays in place.

The ABS wheel material is fully recyclable.

Contents:

2 x Yellow 5 Spoke Injection Molded ABS Wheels.

2 x Rubber O-Ring Tyres.

Wheel Dimensions:

Wheel Diameter (no tire): 63mm.

Wheel Diameter (with tire): 67.5mm.

Max Width:11.75mm.

100g reel of Lead free solder (99.9% tin and copper). This solder incorporates flux.

Features:

Tin 99% / Copper 0.9% composition.

Incorporates flux.

0.7mm solder wire diameter (22SWG).

Contents:

1 x 100g Reel of Lead-Free Solder Wire, Tin.

Reel of heat shrink sleeving (sometimes called heat shrink tubing) in 3.2mm 11m

It shrinks to around half the size when heated. All dimensions and thicknesses shown are pre-heating measurements.

This 3 x AAA battery holder with power leads that terminate in a JST connector. The leads are colour coded and 150mm long. The holder also features two mounting holes so that the battery holder can be permanently mounted on a project or surface.

This battery holder is ideal for any project that requires 4.5V of battery power delivered via a JST connection.

Features:

Holds 3 x AAA Batteries.

Mounting holes allowing for permanent attachments to projects or surfaces.

150mm colour coded leads with a JST connector.

Contents:

1 x (3xAAA) Battery holder with JST connector.

Dimensions:

Length: 52.5mm.

Width: 37.5mm.

Height: 12mm.

This is a 33mm round momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing.

Choose drop down button for colour options.

Features:

Convex Button.

M28 thread.

Rated for 12V/24A.

Contents:

1 x Push Button 33mm, - choose colour

Dimensions:

Height: 46mm.

Diameter: 35.75mm.

Mounting Hole Diameter: 27.3mm.

This 3V vertical submersible low power water pump is an ideal solution for creating a small indoor water feature or as part of a plant watering system. At the heart of the pump is a 3V DC motor that runs quietly and only draws approximately 100mA.

The pump needs priming before use and should be kept fully submerged during use as it will only pump water not air. Also, it only works in one direction as a pump, you cannot reverse the connections and have it move water in the other direction.

It's 3V, 100mA power requirements are such that you could use a microcontroller with suitable drive capacity to switch it on or off. As the new micro:bit now has 200mA available for powering external devices, this pump can be powered directly by the micro:bit V2.

The micro:bit can only drive 15mA from its pins, so a transistor or FET is required to control it from the pins, either in an on/off capacity, or, with PWM to vary pumping rate. If using the original micro:bit or if the microbit is already controlling other devices, this pump can also be powered and controlled via a motor driver board, or similar.

Note:This pump is not supplied with any tubing.

Features:

Vertical type submersible pump.

Operating power requirements are; 3V and 100mA.

Low noise DC motor.

Can be controlled with a simple on/off switch or microcontroller/motor driver board.

Ideal for small water features or plant watering systems.

A flow rate of 80L/H @ 3V and 100L/H at 4.5V.

Contents:

1 x 3V Vertical Submersible Water Pump.

Dimensions:

Length: 38.5mm.

Width: 23.9mm.

Height: 42.6mm.

This 30cm servo extension cable has three 22-AWG wires joining a male Futaba J connector and a female JR connector. Since a female JR connector can be plugged into a male Futaba J connector, each end of the cable is compatible with both Futaba and JR-style connections; this cable will work as an extension cable in either system or as an adapter between systems, and it is compatible with almost all of the servos in the Kitronik range

The connectors have contacts on a 0.1" spacing, and each wire is comprised of 60 strands, making this cable more flexible than standard servo cables.

Features:

Compatible with all standard servo types including a Mini 180 degree servo.

Also compatible with a Mini 360 degree continous rotation servo.

Servo cable colour convention:

Brown or black = ground (GND, battery negative terminal).

Red = servo power (Vservo, battery positive terminal).

Orange, yellow, white, or blue = servo control signal line

This 60cm servo extension cable has three 22-AWG wires joining a male Futaba J connector and a female JR connector. Since a female JR connector can be plugged into a male Futaba J connector, each end of the cable is compatible with both Futaba and JR-style connections; this cable will work as an extension cable in either system or as an adapter between systems, and it is compatible with almost all of the servos in the Kitronik range.

The connectors have gold-flashed contacts on a 0.1" spacing, and each wire is comprised of 60 strands, making this cable more flexible than standard servo cables.

Features:

Compatible with all standard servo types including a Mini 180 degree servo.

Also compatible with a Mini 360 degree continuous rotation servo.

Servo cable colour convention:

Brown or black = ground (GND, battery negative terminal).

Red = servo power (Vservo, battery positive terminal).

Orange, yellow, white, or blue = servo control signal line.