Duratool Desoldering Pump

Ideal for technicians, a comprehensive electronics toolkit supplied within a handy zipped tool bag - external dimensions: 340 x 210 x 50mm.

Kit Contents:

20W/130W Soldering iron

Desoldering pump

Multimeter

5" Long nose pliers

5" Side cutters

Slotted precision screwdriver: 2.5 x 75mm

Phillips precision screwdriver: PH00 x 75mm

Slotted screwdrivers: 4 x 75, 5 x 75, 6 x 125mm

Phillips screwdrivers: PH0 x 75, PH1 x 75, PH2 x 125mm

Mains tester screwdriver

Wire stripper/cutter

8pc Hex key set: 1.5, 2, 2.5, 3, 4, 5, 5.5, 6mm

IC extractor

Tweezers

Great value starter soldering iron kit. Everything you need to start soldering in one handy pack, including a 30W mains powered soldering iron.

Contents:

1 x 30W Soldering iron.

1 x Safety stand.

1 x Desoldering pump.

Lead free solder.

Watch this video below for an explanation of some of the components in the kit (please note: not all items in the video are included in this kit, see contents list for exact contents).

The LED kit contains red, green & yellow LEDs in 3mm, 5mm and 10mm round sizes as well as some Colour Changing and Tri colour LEDs plus some 5mm LED panel mounting holders. 105 parts are supplied in a multiple compartment storage box.

Features:

Large selection of LEDs.

3mm, 5mm and 10mm Red LEDs.

3mm, 5mm and 10mm Green LEDs.

3mm, 5mm and 10mm Yellow LEDs.

5mm LED holders.

Colour Changing LEDs.

Tri colour 5mm diffused LEDs.

Contents:

10 x 3mm Red LEDs.

10 x 5mm Red LEDs.

5 x 10mm Red LEDs.

10 x 3mm Green LEDs.

10 x 5mm Green LEDs.

5 x 10mm Green LEDs.

10 x 3mm Yellow LEDs.

10 x 5mm Yellow LEDs.

5 x 10mm Yellow LEDs.

10 x 5mm Panel Mount LED Clips.

10 x Colour Changing 5mm LEDs.

10 x Tri Colour 5mm LEDs.

1 x LED Kit box.

Kit Box Dimensions:

Length: 174mm.

Width: 140mm.

Height: 32mm.

Compatible with:

Raspberry Pi Pico

Micro:Bit

These are 20cm long jumpers with male connectors on one end and female on the other. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.

Male to Female connectors

Pack of 40 x M/F Jumpers (four of each colour)

Length: 20cm (approx)

These high precision Quartz Clock Mechanisms are great if you want to make your own clock or for replacing faulty clock mechanisms and come with all required fixing hardware and hour, minute and second hands. They are accurate to within 30 seconds per month and run from one AA Battery which lasts over a year. The time is easily set or adjusted with the dial on the back of the unit.

Popular uses include recycling old CDs and laser cutting custom designs from Perspex or plywood to make into clocks, but if you're after a more complete kit you can try our clock making kit, or assemble your own kit from our range of accessories.

Features:

Quality quartz clock movement.

Includes hands and fixings.

Energy-efficient.

Accurate timekeeping.

Contents:

1 x Quartz clock mechanism.

1 x Second hand.

1 x Minute hand.

1 x Hour hand.

1 x Washer.

1 x Fixing nut.

Dimensions:

Width: 54mm

Height: 54mm

Depth: 14mm

These are 20cm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header.

Male to Male connectors

40 x M/M Jumpers (four of each colour)

Length: 20cm (approx)

The colour changing LED on this kit turns on when it goes dark and stays on for a period of time. This makes a good night light and because the LED is only on for a small amount of time the batteries last much longer than a light that is on all night.

There is an on board trimmer to set the light level at which the LED turns on and another trimmer to set how long the LED stays on for. The maximum duration is about 30 minutes. When set to 15 minutes and activated once a night the batteries will last two months.

Features:

Adjustable light level sensor.

Adjustable length of light time.

Contents:

2 x 10K Resistor.

2 x 1M Resistor.

1 x PCB trimmer 220K POT.

1 x PCB trimmer 10M POT.

1 x 47R Resistor.

1 x Miniature LDR.

1 x Capacitor, Electrolytic, 16V, 470uF.

4 x 2N7000 N Chanel FET.

1 x Colour Changing 5mm Diffused LED - 750mCd.

1 x PP3 Battery Clip Lead (Heavy Duty).

1 x 3xAA Battery Cage with Clip.

1 x Timed Night Light Kit PCB.

Dimensions:

PCB Length: 53mm.

PCB Width: 41mm.

Requires:

3 x AA Batteries.

Soldering Iron.

Solder.

Wire Cutters.

This solar cell kit has been put together to provide a renewable power source for the Kitronik Environmental Control Board. Harness the energy of the sun to power your projects. The kit comprises 3 x AA Ni-MH 1300mAh Rechargeable Batteries and a 5.0V 130mA Polycrystalline Solar Cell.

The Environmental Control Board comes supplied with its own onboard battery holder and also a terminal block for attaching solar cells. This add on pack provides everything you need to take advantage of these features, enabling you to make use of sunlight as a power source. Firstly, insert the batteries and then attach the solar cell to the terminal block with a small screwdriver. No soldering required.

Features:

This kit provides a renewable power source for the Kitronik Environmental Control Board.

No soldering required.

Solar Cell Features:

Maximum current: 130mA.

Maximum power: 0.65W.

Rechargeable Batteries Features:

The batteries are rechargeable making them a cost-effective and greener way of powering your projects.

They have a capacity of 1300mAh and a nominal output of 1.2V.

They are of a Nickel Metal Hydride construction.

They have no charging memory effect.

AA Battery type.

Contents:

3 x AA Ni-MH 1300mAh Rechargeable Batteries.

1 x 5.0V 130mA Polycrystalline Solar Cell.