Craft Clockwork Set

Add a touch of class and sophistication to your beverage consumption with these square-shaped slate coasters. Not only do they look stylish and sleek, but they are also durable, practical, and will protect your surfaces from heat and liquids. Although stone/slate cannot be cut with a CO2 laser, they can be laser engraved for that personal touch. They can easily be cleaned with warm water, with a touch of detergent if heavily soiled, and they are as good as new. Supplied as a pack of 4.

These stylish square-shaped coasters will look great in any location.

They are durable, practical, and resistant to scratching and staining.

Protect your tables and surfaces from heat/liquid damage.

Personalise them with CO2 laser engraving, a coat of lacquer will help improve the contrast.

They can easily be wiped clean with warm water, or warm water mixed with a small amount of mild detergent.

The perfect gift for someone special!

If they fade over time they can easily be brought back to life with a little olive oil.

An even coat of lacquer can have a dramatic positive effect on their look.

Length: 100mm (Nominal).

Width: 100mm (Nominal).

Thickness: 5mm (Nominal).

This is a high-quality Italian Poplar Plywood sheet (laserply) that is suitable for a wide range of applications and is particularly suited to laser cutting. Poplar has a lower density than Birch, meaning that it can be easily laser cut at lower power settings.

This Poplar Plywood has an AB grading which is typically the best grade of plywood available.

High-quality poplar laser plywood sheets (laserply)

Low density for easier laser cutting

Top quality AB grading meaning fewer knots aiding consistency of laser cutting

PEFC Certified (Programme for the Endorsement of Forest Certification)

Interior grade glue

1 x 3mm Poplar Laser Plywood (laserply), 600mm x 400mm Sheet

Length: 600mm

Width: 400mm

Height: 3mm

Daler Rowney Graduate Pony Synthetic Round Wash Brush Range

This Daler-Rowney Graduate Pony and Synthetic Round Wash Short Handle Brush are excellent for liquid applications like watercolours. With its fine point, the colour flows perfectly when the brush is wet so you can create detailed and beautiful works of art. Short Handle

High-quality A/B grade Oak Veneered MDF panel measuring 300mm x 200mm. Ideal for structural projects requiring a high-quality appearance and finish on both the topside and panelling. Suitable for laser cutting. This MDF panel is veneered on both faces of the sheet: A grade veneer on the front and B grade on the reverse.

Please note: As wood is a natural product, there is often a crook or bow to the sheet. The natural twist might be in excess of 10mm (see below - Tolerances and Caution). A wood veneer is not like an artificial surface such as melamine or a laminate. It is cut from the log and therefore has its own unique grain, texture, and colour.

A Grade Veneer is a very high-quality grading (typically the best you will see). The surface of the material will be consistent in appearance with no large variations in colour. Small pin knots are allowed and these would typically be only a few mm in diameter. This grade veneer is on the topside of this MDF sheet.

The B Grade Veneer underside shows the natural look of the veneer. There will be changes in colour that show the grain pattern. Sound, smooth knots are allowed and these will typically be under 15mm to 35mm in diameter (depending on the countries grading rules). The surface should normally be free from open knots and plugs. The material should be suitable for paint/stain or a lacquered finish.

There are two different cuts that can be used in veneer production:

'Quarter Cut' are cut at 90 degrees, producing the effect of a straight grain.

'Crown Cut' are sliced through the log, producing 'Crowns' and adding more character to the finish (as used on this product). This product conforms to E1 (low) formaldehyde levels and is often described as 'Laser Grade' MDF but there is no official classification for this. We believe that E1 conforming MDF is the safest and best MDF for using in a laser cutter.

Features:

A/B grade Oak Veneered finish.

Veneer thickness approximately 0.5mm.

High-quality wood and veneer, for great-looking finishes.

MDF core.

Suitable for use in internal dry conditions as defined in EN 622 parts 1 and 5 and conforms to EN13986.

Low formaldehyde emissions.

Dimensions:

Length: 300mm.

Width: 200mm.

Height: 4mm.

Veneer thickness (approximately): 0.5mm.

Tolerances: The manufacturing tolerance for the thickness of veneered MDF sheets includes the tolerance for both the MDF and the veneer. The total combined thickness of both the MDF and the veneer could be as little as 3.35mm and as much as 4.65mm. The veneer on each face could be as thin as 0.25mm and as thick as 0.75mm.

Caution: As wood is a natural product there is often a bow or crook to the MDF, and in some cases a twist. We have measured in excess of 10mm rise between the flat centre of the MDF and the corner. l. If you are using this product on a laser cutter; these sheets should be strapped/taped to the laser bed before cutting.